E-Z WAY APPLICATOR

K-100 E-Z Way Applicator

k100

It incorporates a 2 1/2 gallon polyethylene tank with a flow control valve adjustment. It also includes a complete frame assembly with plastic lower plate and manifold tube section for dispensing your product. 

The applicator is a great time saver. One operator can easily do the job of three or more persons and the 2 1/2 gallon tank is sufficient enough to apply wax up to 7500 square feet of floor surface depending on heaviness of application. 

The applicator was designed for applying WATER based products, such as wax and water based gym finish, asphalt, vinyl tile, terrazzo, paver tile, concrete or wood floor. 

When applying wax or gym finish make sure that you use separate applicators to apply either finish. DO NOT USE THE SAME APPLICATOR. You will contaminate the tank and compromise your job. 

There are two different pads available for your choice depending on the finish you are applying. 

The KV-2400 is a long napped poly-blend pad made of cotton and polyester,is 24" inches long with grommets that attaches easily to the frame assembly, and is designed for wax application. 

The KV-4400 is a 24" inch Synthetic lambswool pad that is designed to apply water based gym finish. 

The Pads are not included with the applicator. They are sold separately in a case of twelve pads each.

K-200 E-Z Way Applicator

k200

The manifold has been made of aluminum to resist solvent attack. The frame assembly has a wood base to provide the stability found in standard lamb's wool applicators and a specially designed synthetic lamb's wool pad to aid in the application of a smooth, uniform coating. 

Aside from these necessary changes for the handling of solvent based coatings, this model gives you all the outstanding advantages of the original E-Z Way, such as: 

Light weight portability - Completely assembled it weighs ten pounds. 

Self-contained gravity fed system - no cumbersome pressure tanks required. 

Time, work and money saving one-man operation, covering as much as 10,000 sq. ft. in less than two hours, as opposed to about 10 man hours of work with the traditional wood block applicator. Think of the money saved in a year's time! 

Uniform application - positive control of the coating which eliminates the back-breaking job of feathering out the finish. 

No wasting material. The coating material is never contaminated, so there's no need to throw away any leftover material. Just empty it back into the original container for use on the next job. 

All pads on the applicator can be replaced if a part should break or wear out.

K-450 E-Z Way Applicator

File Name : DSC_0016.JPG
File Size : 2.4MB (2509453 Bytes)
Date Taken : 2003/06/12 15:19:59
Image Size : 3008 x 1960 pixels
Resolution : 300 x 300 dpi
Bit Depth : 8 bits/channel
Protection Attribute : Off
Hide Attribute : Off
Camera ID : N/A
Camera : NIKON D1X
Quality Mode : FINE
Metering Mode : Spot
Exposure Mode : Manual
Speed Light : No
Focal Length : 42 mm
Shutter Speed : 1/60 second
Aperture : F13.0
Exposure Compensation : 0 EV
White Balance : Preset 1
Lens : 28 - 300 mm F 3.5 - 6.3
Flash Sync Mode : N/A
Exposure Difference : -5.2 EV
Flexible Program : No
Sensitivity : ISO400
Sharpening : High
Image Type : Color
Color Mode : Mode II(Adobe RGB)
Hue Adjustment : 3
Saturation Control : N/A
Tone Compensation : Normal
Latitude(GPS) : N/A
Longitude(GPS) : N/A
Altitude(GPS) : N/A

It has a double valved independent delivery system that applies the material directly to the floor and allows you to adjust the flow where you need it. Since it does not have the manifold tube feed system it allows for easier clean up. 

The applicator comes with a KV-4400 pad included with this unit. 

All E-Z Way applicators are lightweight, completely self-contained gravity fed systems. It allows you to complete your job in one third the time compared to the mop-and-bucket method. 

As with the other applicators your solution will not be contaminated and can be emptied back into the original container. 

All pads on the applicator can be replaced if a part should break or wear out.

Replacement Pads

replacement-pads-1

Have Questions?